Freeswitch 1.10 installation on Debian 10

2 min read

A short, step-by-step guide for proper installation of Freeswitch 1.10 on Debian 10 (buster)

The official instructions are barebone, so this guide is a supplement covering the most important steps to finish with a working system.

Root login

After Debian 10 installation, it is impossible to login with the root from outside. Let’s fix that.

sed -i "s|PermitRootLogin without-password\+|PermitRootLogin yes|g" /etc/ssh/sshd_config
systemctl restart sshd

Time sync service

Now, let’s install the service that automatically syncs the system clock to prevent installation problems:

apt -y install chrony
systemctl start chrony
systemctl enable chrony

You may get a similar error when installing:

/debian/dists/buster/InRelease is not valid yet (invalid for another 19h 54min 54s). Updates for this repository will not be applied.

This means that the system clock is off-sync and that you skipped this step.

System upgrade

You will need to upgrade the system with the latest packets:

apt-get update && apt-get -y dist-upgrade

Based on your system and internet speed, this can take up to several minutes.

After the new packets are installed, reboot the system and relogin:

reboot

Freeswitch installation

Now we can execute official steps to install Freeswitch:

apt-get update && apt-get install -y gnupg2 wget lsb-release
wget -O - https://files.freeswitch.org/repo/deb/debian-release/fsstretch-archive-keyring.asc | apt-key add -
echo "deb http://files.freeswitch.org/repo/deb/debian-release/ `lsb_release -sc` main" > /etc/apt/sources.list.d/freeswitch.list
echo "deb-src http://files.freeswitch.org/repo/deb/debian-release/ `lsb_release -sc` main" >> /etc/apt/sources.list.d/freeswitch.list
apt-get update && apt-get install -y freeswitch-meta-all

After these steps, the official guide tells you to access Freeswitch with the command:

fs_cli -rRS

However, this command will fail:

[ERROR] fs_cli.c:1691 main() Error Connecting []
[INFO] fs_cli.c:1697 main() Retrying

The reason it will fail is because after installation, Freeswitch is not automatically started. Let’s start it:

systemctl start freeswitch

Also let’s enable it to start on system reboot:

systemctl enable freeswitch

Now, we can access Freeswitch:

fs_cli

If you get an error, it is possible that Freeswitch has not started yet. Sometimes it takes up to 20 s until it is operational.

If after 20 s fs_cli returns an error, you will need to check it with these commands:

apt-get -y install net-tools
netstat -vatupn | grep freeswitch | grep 8081

The output should show two lines, similar to these (some numbers will be different):

tcp 0 0 192.168.1.195:8081 0.0.0.0:* LISTEN 43246/freeswitch
tcp6 0 0 ::1:8081 :::* LISTEN 43246/freeswitch

If you don’t see the above output, Freeswitch has failed to start, and the console (whose port is 8081) is not reachable.

Restart Freeswitch with:

systemctl restart freeswitch

If this does not help, check Freeswitch status with:

systemctl status freeswitch

If an error is shown, then follow the guidelines described in the output to get more details about the problem and solve it. (Troubleshooting Freeswitch service startup is an extensive topic that will not be covered in this article.)

Exit from fs_cli with /bye, /exit or /quit command.

Additional Services

You will need to install/activate several services for the Freeswitch server.

DNS caching:

apt -y install unbound
sed -i "s|#prepend domain-name-servers 127.0.0.1\+|prepend domain-name-servers 127.0.0.1|g" /etc/dhcp/dhclient.conf
systemctl start unbound
systemctl enable unbound

You will also need to enable the proper entropy source for cryptography operations:

apt-get -y install haveged
haveged -w 1024
systemctl enable haveged.service
systemctl start haveged.service

These help Freeswitch to run more smoothly.

G729 codec installation for transcoding

Freeswitch comes with G729 codec only for pass-through, which means if one call leg has G729 codec and another has a different codec, the call will fail because Freeswitch will be unable to transcode to/from G729 codec.

To solve this, royalty-free (as of Jan 1 2017) G729 codec can be installed with transcoding capabilities.

apt-get -y install libfreeswitch-dev git autoconf automake libtool
cd /usr/src/
git clone https://github.com/xadhoom/mod_bcg729.git
cd mod_bcg729
make && make install
sed -i "s|mod_g729\+|mod_bcg729|g" /etc/freeswitch/autoload_configs/modules.conf.xml

Restart Freeswitch:

systemctl restart freeswitch

And check if codec is loaded properly:

fs_cli -x "show codecs" b | grep g729

The result should be:

codec,G.729,mod_bcg729

Conclusion

The procedure described in this article will help you install Freeswitch on the Debian 10 together with additional steps for system operation. Let us know if you have additional questions on completing each step. Happy Freeswitching!

5 Replies to “Freeswitch 1.10 installation on Debian 10”

  1. Mon professeur de téléphonie IP m’as donner un thème sur l’installation et la configuration de freeswitch sur debian 10 et que les appels passe entre les Androids

Leave a Reply

Your email address will not be published. Required fields are marked *